Chlorine Transer Hose
Chemfluor® PTFE Fluoropolymer Helically Convoluted Inner Tube PVDF (Kynar®) Braids
 | Applications |
- Tank car loading/unloading
- Pulp and paper bleaching
- Chemical transfer
|
| Common Media |
- Chlorine
- Bromine
- Sodium hydroxide
- Sulfuric and hydrochloric acids
- Other corrosive materials
|
| Features & Benefits |
- Unexcelled chemical resistance for longer service life
- Not subject to stress corrosion, pinholing or flex cracking
- Convoluted inner tube is low profile and helical formed to promote self-drainage
- Moisture will not affect inner tube
- Does not need to be cleaned and capped after every use
- Minimum pressure drop for faster loading and unloading
- Lightweight and ultra flexible for handling ease
- Low force to bend
- Can be inspected safely
- Less costly than Monel® (metal hose)
- Wide hex flats for easy wrenching
|
| Details |
Construction: - Inner Tube: One-piece extruded Chemfluor® natural PTFE fluoropolymer
--No seams or voids - Cover: Thick-strand chafe-resistant PVDF (Kynar®)
--Protects against abrasion - Reinforcement: Two high tensile strength PVDF (Kynar®) braids
--For high pressure rating
Fittings - Standard: Schedule 80 Monel® stub end 300# epoxy coated carbon steel lap-joint flange
- Schedule 80 Monel® hex male NPT (1" wide wrenching flats)
--Schedule 80 Monel® R405 male NPT or Schedule 80 stub end available - Internal Monel® crimp ferrule locks fitting to inner tube and two reinforcement braids
|
| Engineering Specifications | Industry Approvals Compliances |
Temperature Rating- -40°F to +120°F
- -40°C to +49°C
| - Manufactured in accordance with Chlorine Institute Pamphlet 6 piping specifications
|
| Maximum Length |
| 1/2" | 30' OAL |
| 1" | 50' OAL |
| 1-1/2" | 30' OAL |
| Quality Control and Testing |
- Each hose is material lot traceable
- Each hose is subject to stringent QC procedures throughout the manufacturing process
- Each hose is permanently identified in accordance with Chlorine Institute specifications
- Each hose is thoroughly cleaned before assembly; no oils, solvents or other contaminants are used in the assembly process
- Each hose is pressure tested with nitrogen gas at twice the rated operating pressure while fully submerged under water
- Each hose is dried and capped for shipment
- A unique serial number is applied to each end of the hose for further traceability; permanent log of all hose assemblies maintained at factory
|
Stainless steel crimp ring secures PVDF (Kynar®) abrasion cover. A permanent stainless steel ID band provides the following information:- "Flexible Components"
- "For Chlorine Service"
- Date of manufacture
- Maximum allowable working pressure
- Usable temperature range
- Minimum bend radius
- Test pressure
|  |
CL Series Hose Specifications
| Part Number | Inside Diameter | Outside Diameter | Max Working Pressure | Min Burst Pressure | Min Bend Radius |
| in. | mm. | in. | mm. | PSI | Mpa | PSI | Mpa | in. | mm. |
| 8CLXXXXMKY | 1/2 | 12.7 | 1 | 26.0 | 500 | 3.45 | 2,500 | 17.24 | 2.50 | 63.50 |
| 16CLXXXXMKY | 1 | 25.4 | 1-5/8 | 41.9 | 375 | 2.59 | 1,875 | 12.93 | 8.00 | 203.20 |
| 24LXXXXMKY | 1-1/2 | 38.1 | 2-1/8 | 54.0 | 375 | 2.59 | 1,875 | 12.93 | 10.00 | 254.00 |
Burst Pressure ratings at ambient 70ºF (21ºC).
Important note regarding part numbers: The X's shown in part numbers are replaced with 03 (NPT) and/or 12 (Flange Lap Joint Style), depending on the type of fitting specified for the assembly. For example, the part number for a 1/2" assembly featuring NPT fittings at both ends would be 8CL0303MKY. The part number for a 1" assembly with an NPT fitting at one end and a flange fitting at the other would be 16CL0312MKY. When both fittings are flanged, add a second "M" to the part number; in this case, the part number for a 1-1/2" assembly would be 24CL1212MMKY.
Choose flanged material: C3 = 300 lbs. carbon steel 300#; 43 = 304 stainless steel 300#; 63 = 316 stainless steel 300#. Check for ordering information (Document PDF at right).
These hoses are not metrically sized; metric dimensions provided as a convenience only.
Test Pressure = 2x maximum operating pressure.
XXXX indicates fitting styles. Check for fitting style indicators and assembly part number details (Document PDF at right).
 | For assistance, call:
+1 800-435-3992
|